{"title":"500mm Footprint","description":"\u003cp\u003eFor objects to about 350mm across, and for small groups of objects on one plate.\u003c\/p\u003e\u003cp\u003e500mm is where a plinth starts reading as furniture rather than as a pedestal, so keep the height honest — 500 square at 450mm high is a low table to most visitors, whatever you intended, and things get put on it.\u003c\/p\u003e","products":[{"product_id":"display-plinth-500mm-by-500mm-by-900mm-high-in-terrazzo","title":"Display Plinth 500mm by 500mm by 900mm High in Terrazzo","description":"\u003cp\u003eA 500mm square plinth at 900mm tall, in terrazzo. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 900mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: cast terrazzo with a marble aggregate, ground and sealed, no two panels the same\u003c\/li\u003e\n\u003cli\u003eFinish: cast terrazzo with a marble aggregate, ground and sealed, no two panels the same\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: three point levelling, because three points always sit flat on a gallery floor and four points never do\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: crated, kerbside on a pallet unless you book the two person service, which we recommend\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 72.9 kilograms\u003c\/li\u003e\n\u003cli\u003eHollow, and it can be weighted through the access panel if the object is light\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, cast in one piece\u003c\/li\u003e\n\u003cli\u003eThree levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443152204,"sku":"PLS-PLI-012-ST","price":1174.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443184972,"sku":"PLS-PLI-012-CT","price":1249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_900mm_High_in_Terrazzo.jpg?v=1789057365"},{"product_id":"display-plinth-500mm-by-500mm-by-900mm-high-in-corian","title":"Display Plinth 500mm by 500mm by 900mm High in Corian","description":"\u003cp\u003eA 500mm square plinth at 900mm tall, in corian. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 900mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: solid surface with the joints bonded and sanded flush, so a large plinth reads as one piece of material with no visible seam\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 39.6 kilograms\u003c\/li\u003e\n\u003cli\u003eHollow, and it can be weighted through the access panel if the object is light\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443217740,"sku":"PLS-PLI-013-ST","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443250508,"sku":"PLS-PLI-013-CT","price":1224.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_900mm_High_in_Corian.jpg?v=1789057368"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-solid-oak","title":"Display Plinth 500mm by 500mm by 1100mm High in Solid Oak","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in solid oak. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: solid European oak, 20mm panels on a braced frame, finished in a hardwax oil\u003c\/li\u003e\n\u003cli\u003eFinish: solid European oak, 20mm panels on a braced frame, finished in a hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 41.5 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall, which is why it does not tip\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443283276,"sku":"PLS-PLI-014-ST","price":1174.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443316044,"sku":"PLS-PLI-014-CT","price":1224.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Solid_Oak.jpg?v=1789057387"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-solid-ash","title":"Display Plinth 500mm by 500mm by 1100mm High in Solid Ash","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in solid ash. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: solid English ash, pale and straight grained, finished in hardwax oil\u003c\/li\u003e\n\u003cli\u003eFinish: solid English ash, pale and straight grained, finished in hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 39.3 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall, which is why it does not tip\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443348812,"sku":"PLS-PLI-015-ST","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443381580,"sku":"PLS-PLI-015-CT","price":1099.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Solid_Ash.jpg?v=1789057366"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-brushed-brass","title":"Display Plinth 500mm by 500mm by 1100mm High in Brushed Brass","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in brushed brass. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 1.5mm brass sheet over a steel armature, brushed and lacquered, or left unlacquered to patinate if you ask\u003c\/li\u003e\n\u003cli\u003eFinish: 1.5mm brass sheet over a steel armature, brushed and lacquered, or left unlacquered to patinate if you ask\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 52.6 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall, which is why it does not tip\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443414348,"sku":"PLS-PLI-016-ST","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443447116,"sku":"PLS-PLI-016-CT","price":1649.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Brushed_Brass.jpg?v=1789057381"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-polished-concrete","title":"Display Plinth 500mm by 500mm by 1100mm High in Polished Concrete","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in polished concrete. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: glass fibre reinforced concrete, cast in one piece and diamond polished, which is heavy and is meant to be\u003c\/li\u003e\n\u003cli\u003eFinish: glass fibre reinforced concrete, cast in one piece and diamond polished, which is heavy and is meant to be\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: three point levelling, because three points always sit flat on a gallery floor and four points never do\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: crated, kerbside on a pallet unless you book the two person service, which we recommend\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 89.0 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall, which is why it does not tip\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, cast in one piece\u003c\/li\u003e\n\u003cli\u003eThree levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443479884,"sku":"PLS-PLI-017-ST","price":1124.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443512652,"sku":"PLS-PLI-017-CT","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Polished_Concrete.jpg?v=1789057394"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-terrazzo","title":"Display Plinth 500mm by 500mm by 1100mm High in Terrazzo","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in terrazzo. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: cast terrazzo with a marble aggregate, ground and sealed, no two panels the same\u003c\/li\u003e\n\u003cli\u003eFinish: cast terrazzo with a marble aggregate, ground and sealed, no two panels the same\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: three point levelling, because three points always sit flat on a gallery floor and four points never do\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: crated, kerbside on a pallet unless you book the two person service, which we recommend\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 85.3 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall, which is why it does not tip\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, cast in one piece\u003c\/li\u003e\n\u003cli\u003eThree levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443676492,"sku":"PLS-PLI-018-ST","price":1374.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443709260,"sku":"PLS-PLI-018-CT","price":1449.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Terrazzo.jpg?v=1789057369"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-corian","title":"Display Plinth 500mm by 500mm by 1100mm High in Corian","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in corian. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: solid surface with the joints bonded and sanded flush, so a large plinth reads as one piece of material with no visible seam\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 46.3 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall, which is why it does not tip\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785443774796,"sku":"PLS-PLI-019-ST","price":1324.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785443807564,"sku":"PLS-PLI-019-CT","price":1399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Corian.jpg?v=1789057369"},{"product_id":"freestanding-vitrine-500mm-by-500mm-by-1400mm-high-with-a-gallery-white-lacquer-base","title":"Freestanding Vitrine 500mm by 500mm by 1400mm High with a Gallery White Lacquer Base","description":"\u003cp\u003eA full height glass case on a gallery white lacquer base, sized for a medium object with room to walk around it, on a base that brings the work to eye level.\u003c\/p\u003e\u003cp\u003eA vitrine is a box that has to disappear. Everything we do to one is aimed at that: low iron glass because ordinary float glass has a green cast that shows on every edge, mitred and polished glass corners rather than an aluminium post, and a base sized so the glass sits proud of it rather than inside a visible rebate. The unglamorous half is the part that keeps the object safe. Dust gets in through the base, not the top, so every case here has a gasketed base and a felt sealed door, which is the single biggest thing you can do for anything that has to stay clean for ten years.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1400mm high overall\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal display area 480mm by 480mm by 660mm high\u003c\/li\u003e\n\u003cli\u003eConstruction: welded steel armature inside a gallery white lacquer base, glass mitred and polished at every vertical corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm moisture resistant MDF sprayed in a two pack polyurethane to RAL 9010, which is the white almost every gallery in the country paints its walls\u003c\/li\u003e\n\u003cli\u003eLoad rating: 142kg on the deck, 15kg per glass shelf\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: hinged door with a concealed lock, keyed alike across an order\u003c\/li\u003e\n\u003cli\u003eDelivery: crated, kerbside on a pallet unless you book the two person service, which we recommend\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 62.0 kilograms\u003c\/li\u003e\n\u003cli\u003eGlass: 6mm, mitred and polished, choose the specification at order\u003c\/li\u003e\n\u003cli\u003eDust: gasketed base and a felt sealed door, which is what keeps it clean\u003c\/li\u003e\n\u003cli\u003eDoor: hinged on the long side, opening 100 degrees, needs 600mm of swing\u003c\/li\u003e\n\u003cli\u003eShelves: one glass deck included, extra shelves available\u003c\/li\u003e\n\u003cli\u003eCable entry: a grommet in the base for a lighting or humidity lead\u003c\/li\u003e\n\u003cli\u003eBase height: 700mm, which is the standard for a case of this size\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe base, flat packed, with a welded steel armature\u003c\/li\u003e\n\u003cli\u003eThe glass case, assembled in its own crate\u003c\/li\u003e\n\u003cli\u003eOne glass deck shelf\u003c\/li\u003e\n\u003cli\u003eA concealed lock with two keys\u003c\/li\u003e\n\u003cli\u003eLevelling feet, gaskets and a cable grommet\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eThe base arrives flat packed and the glass arrives assembled in its own crate. Build and level the base first, then two people lift the glass on. Do not lift a glass case by the top rail. The gasket seats itself under the weight of the glass, so leave it for an hour before you load the case and check the door line again after a day.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Toughened float glass","offer_id":58785448001868,"sku":"PLS-VIT-002-TG","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Low iron glass, no green edge","offer_id":58785448034636,"sku":"PLS-VIT-002-LI","price":1349.0,"currency_code":"GBP","in_stock":true},{"title":"Laminated UV filtering glass","offer_id":58785448067404,"sku":"PLS-VIT-002-UV","price":1524.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Freestanding_Vitrine_500mm_by_500mm_by_1400mm_High_with_a_Gallery_White_Lacquer_Base.jpg?v=1789126082"},{"product_id":"freestanding-vitrine-500mm-by-500mm-by-1400mm-high-with-a-solid-oak-base","title":"Freestanding Vitrine 500mm by 500mm by 1400mm High with a Solid Oak Base","description":"\u003cp\u003eA full height glass case on a solid oak base, sized for a medium object with room to walk around it, on a base that brings the work to eye level.\u003c\/p\u003e\u003cp\u003eA vitrine is a box that has to disappear. Everything we do to one is aimed at that: low iron glass because ordinary float glass has a green cast that shows on every edge, mitred and polished glass corners rather than an aluminium post, and a base sized so the glass sits proud of it rather than inside a visible rebate. The unglamorous half is the part that keeps the object safe. Dust gets in through the base, not the top, so every case here has a gasketed base and a felt sealed door, which is the single biggest thing you can do for anything that has to stay clean for ten years.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1400mm high overall\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal display area 480mm by 480mm by 660mm high\u003c\/li\u003e\n\u003cli\u003eConstruction: welded steel armature inside a solid oak base, glass mitred and polished at every vertical corner\u003c\/li\u003e\n\u003cli\u003eFinish: solid European oak, 20mm panels on a braced frame, finished in a hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 142kg on the deck, 15kg per glass shelf\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: hinged door with a concealed lock, keyed alike across an order\u003c\/li\u003e\n\u003cli\u003eDelivery: crated, kerbside on a pallet unless you book the two person service, which we recommend\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 69.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGlass: 6mm, mitred and polished, choose the specification at order\u003c\/li\u003e\n\u003cli\u003eDust: gasketed base and a felt sealed door, which is what keeps it clean\u003c\/li\u003e\n\u003cli\u003eDoor: hinged on the long side, opening 100 degrees, needs 600mm of swing\u003c\/li\u003e\n\u003cli\u003eShelves: one glass deck included, extra shelves available\u003c\/li\u003e\n\u003cli\u003eCable entry: a grommet in the base for a lighting or humidity lead\u003c\/li\u003e\n\u003cli\u003eBase height: 700mm, which is the standard for a case of this size\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe base, flat packed, with a welded steel armature\u003c\/li\u003e\n\u003cli\u003eThe glass case, assembled in its own crate\u003c\/li\u003e\n\u003cli\u003eOne glass deck shelf\u003c\/li\u003e\n\u003cli\u003eA concealed lock with two keys\u003c\/li\u003e\n\u003cli\u003eLevelling feet, gaskets and a cable grommet\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eThe base arrives flat packed and the glass arrives assembled in its own crate. Build and level the base first, then two people lift the glass on. Do not lift a glass case by the top rail. The gasket seats itself under the weight of the glass, so leave it for an hour before you load the case and check the door line again after a day.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Toughened float glass","offer_id":58785448198476,"sku":"PLS-VIT-004-TG","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"Low iron glass, no green edge","offer_id":58785448231244,"sku":"PLS-VIT-004-LI","price":1874.0,"currency_code":"GBP","in_stock":true},{"title":"Laminated UV filtering glass","offer_id":58785448264012,"sku":"PLS-VIT-004-UV","price":2124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Freestanding_Vitrine_500mm_by_500mm_by_1400mm_High_with_a_Solid_Oak_Base.jpg?v=1789126073"},{"product_id":"conservation-display-case-500mm-by-500mm-by-1400mm-high-with-humidity-control-in-gallery-white-lacquer","title":"Conservation Display Case 500mm by 500mm by 1400mm High with Humidity Control in Gallery White Lacquer","description":"\u003cp\u003eA sealed case with a silica gel well and laminated UV filtering glass throughout, for a single light sensitive object, a textile fragment or a small work on paper.\u003c\/p\u003e\u003cp\u003eConservation display is a different job from retail display and the specification reflects it. Laminated UV filtering glass takes out essentially all the ultraviolet, which is what fades a watercolour and embrittles a textile. A sealed case with a silica gel well buffers humidity, so an object inside it does not follow every swing of the room around it. Materials are chosen for what they give off as well as what they look like, because MDF and some adhesives release acids that will tarnish silver and corrode lead inside a sealed case, which is why the interior of these ones is lined and sealed rather than simply painted.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1400mm high overall\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal display area 460mm by 460mm\u003c\/li\u003e\n\u003cli\u003eConstruction: sealed carcass with an aluminium honeycomb deck and a foil vapour barrier behind the lining\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm moisture resistant MDF sprayed in a two pack polyurethane to RAL 9010, which is the white almost every gallery in the country paints its walls\u003c\/li\u003e\n\u003cli\u003eLoad rating: 110kg on the deck\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: museum lock as standard, keyed to your existing suite on request\u003c\/li\u003e\n\u003cli\u003eDelivery: crated, kerbside on a pallet unless you book the two person service, which we recommend\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 68.0 kilograms\u003c\/li\u003e\n\u003cli\u003eGlass: laminated UV filtering as standard, transmission under 1 per cent below 380 nanometres\u003c\/li\u003e\n\u003cli\u003eAir exchange rate: under 0.3 volumes a day, tested on every case\u003c\/li\u003e\n\u003cli\u003eHumidity: a silica gel well under the deck, holding 2kg of conditioned gel, accessible without disturbing the object\u003c\/li\u003e\n\u003cli\u003eMaterials: tested to the Oddy method, no acid emitting board or adhesive inside the seal\u003c\/li\u003e\n\u003cli\u003eLighting: no lamp fitted, and a fibre optic gland is provided if you want one, because a lamp inside a sealed case is a heat source\u003c\/li\u003e\n\u003cli\u003eDocumentation: a case data sheet with the air exchange test result\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe sealed carcass with the vapour barrier and lining fitted\u003c\/li\u003e\n\u003cli\u003eThe laminated UV filtering glass case, crated separately\u003c\/li\u003e\n\u003cli\u003eAn aluminium honeycomb display deck\u003c\/li\u003e\n\u003cli\u003eA silica gel well with 2kg of conditioned gel\u003c\/li\u003e\n\u003cli\u003eA museum lock with two keys\u003c\/li\u003e\n\u003cli\u003eA case data sheet and the Oddy test certificates\u003c\/li\u003e\n\u003cli\u003eLevelling feet, gaskets and a fibre optic gland\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eThe base arrives flat packed and the glass arrives assembled in its own crate. Build and level the base first, then two people lift the glass on. Do not lift a glass case by the top rail. The gasket seats itself under the weight of the glass, so leave it for an hour before you load the case and check the door line again after a day.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"No lock","offer_id":58785457602892,"sku":"PLS-CON-001-NL","price":1749.0,"currency_code":"GBP","in_stock":true},{"title":"Cam lock, keyed alike","offer_id":58785457635660,"sku":"PLS-CON-001-CL","price":1824.0,"currency_code":"GBP","in_stock":true},{"title":"Museum lock, keyed to your suite","offer_id":58785457668428,"sku":"PLS-CON-001-ML","price":1899.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Conservation_Display_Case_500mm_by_500mm_by_1400mm_High_with_Humidity_Control_in_Gallery_White_Lacquer.jpg?v=1789057370"},{"product_id":"set-of-three-plinths-500mm-square-graduated-in-gallery-white-lacquer","title":"Set of Three Plinths 500mm Square Graduated in Gallery White Lacquer","description":"\u003cp\u003eThe wider version of the graduated three, for objects that need a bigger top than a 400mm square gives them.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: Three plinths at 500mm square, heights 700mm, 900mm, 1100mm\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm on every plinth in the set\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm moisture resistant MDF sprayed in a two pack polyurethane to RAL 9010, which is the white almost every gallery in the country paints its walls, sprayed in one batch so the whole set matches\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg per plinth evenly distributed\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no locks, these are open plinths\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 95.1 kilograms for the set\u003c\/li\u003e\n\u003cli\u003eSet contains three plinths\u003c\/li\u003e\n\u003cli\u003eFinish: sprayed as one batch, which is why a set matches and three separate orders do not\u003c\/li\u003e\n\u003cli\u003eSaving against buying them singly: about 10 per cent\u003c\/li\u003e\n\u003cli\u003eBallasted on anything over 900mm\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eExtra plinths can be added later and we keep the batch record for five years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThree plinths, flat packed\u003c\/li\u003e\n\u003cli\u003eLevelling feet for every plinth\u003c\/li\u003e\n\u003cli\u003eAn access panel in each with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 100ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003cli\u003eA layout card with three arrangements that work\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785468383564,"sku":"PLS-PST-015-ST","price":1974.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785468416332,"sku":"PLS-PST-015-CT","price":2074.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Set_of_Three_Plinths_500mm_Square_Graduated_in_Gallery_White_Lacquer.jpg?v=1789126068"},{"product_id":"set-of-three-plinths-500mm-square-graduated-in-matt-black-lacquer","title":"Set of Three Plinths 500mm Square Graduated in Matt Black Lacquer","description":"\u003cp\u003eThe wider version of the graduated three, for objects that need a bigger top than a 400mm square gives them.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: Three plinths at 500mm square, heights 700mm, 900mm, 1100mm\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm on every plinth in the set\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm MDF sprayed in a two pack polyurethane to RAL 9005 in a dead matt, which swallows reflections and is why photographers ask for it, sprayed in one batch so the whole set matches\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg per plinth evenly distributed\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no locks, these are open plinths\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 95.1 kilograms for the set\u003c\/li\u003e\n\u003cli\u003eSet contains three plinths\u003c\/li\u003e\n\u003cli\u003eFinish: sprayed as one batch, which is why a set matches and three separate orders do not\u003c\/li\u003e\n\u003cli\u003eSaving against buying them singly: about 10 per cent\u003c\/li\u003e\n\u003cli\u003eBallasted on anything over 900mm\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eExtra plinths can be added later and we keep the batch record for five years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThree plinths, flat packed\u003c\/li\u003e\n\u003cli\u003eLevelling feet for every plinth\u003c\/li\u003e\n\u003cli\u003eAn access panel in each with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 100ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003cli\u003eA layout card with three arrangements that work\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785468449100,"sku":"PLS-PST-016-ST","price":1999.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785468481868,"sku":"PLS-PST-016-CT","price":2124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Set_of_Three_Plinths_500mm_Square_Graduated_in_Matt_Black_Lacquer.jpg?v=1789126068"},{"product_id":"set-of-three-plinths-500mm-square-graduated-in-birch-plywood","title":"Set of Three Plinths 500mm Square Graduated in Birch Plywood","description":"\u003cp\u003eThe wider version of the graduated three, for objects that need a bigger top than a 400mm square gives them.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: Three plinths at 500mm square, heights 700mm, 900mm, 1100mm\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm on every plinth in the set\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18 layer birch plywood with the edge exposed and lacquered, so the layers read as a fine stripe around every corner, sprayed in one batch so the whole set matches\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg per plinth evenly distributed\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no locks, these are open plinths\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 89.4 kilograms for the set\u003c\/li\u003e\n\u003cli\u003eSet contains three plinths\u003c\/li\u003e\n\u003cli\u003eFinish: sprayed as one batch, which is why a set matches and three separate orders do not\u003c\/li\u003e\n\u003cli\u003eSaving against buying them singly: about 10 per cent\u003c\/li\u003e\n\u003cli\u003eBallasted on anything over 900mm\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eExtra plinths can be added later and we keep the batch record for five years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThree plinths, flat packed\u003c\/li\u003e\n\u003cli\u003eLevelling feet for every plinth\u003c\/li\u003e\n\u003cli\u003eAn access panel in each with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 100ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003cli\u003eA layout card with three arrangements that work\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785468547404,"sku":"PLS-PST-017-ST","price":1724.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785468580172,"sku":"PLS-PST-017-CT","price":1824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Set_of_Three_Plinths_500mm_Square_Graduated_in_Birch_Plywood.jpg?v=1789126094"},{"product_id":"set-of-three-plinths-500mm-square-graduated-in-solid-oak","title":"Set of Three Plinths 500mm Square Graduated in Solid Oak","description":"\u003cp\u003eThe wider version of the graduated three, for objects that need a bigger top than a 400mm square gives them.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: Three plinths at 500mm square, heights 700mm, 900mm, 1100mm\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm on every plinth in the set\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: solid European oak, 20mm panels on a braced frame, finished in a hardwax oil, sprayed in one batch so the whole set matches\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg per plinth evenly distributed\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no locks, these are open plinths\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 106.4 kilograms for the set\u003c\/li\u003e\n\u003cli\u003eSet contains three plinths\u003c\/li\u003e\n\u003cli\u003eFinish: sprayed as one batch, which is why a set matches and three separate orders do not\u003c\/li\u003e\n\u003cli\u003eSaving against buying them singly: about 10 per cent\u003c\/li\u003e\n\u003cli\u003eBallasted on anything over 900mm\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eExtra plinths can be added later and we keep the batch record for five years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThree plinths, flat packed\u003c\/li\u003e\n\u003cli\u003eLevelling feet for every plinth\u003c\/li\u003e\n\u003cli\u003eAn access panel in each with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 100ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003cli\u003eA layout card with three arrangements that work\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785468776780,"sku":"PLS-PST-018-ST","price":2724.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785468809548,"sku":"PLS-PST-018-CT","price":2874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Set_of_Three_Plinths_500mm_Square_Graduated_in_Solid_Oak.jpg?v=1789126086"},{"product_id":"set-of-three-plinths-500mm-square-graduated-in-solid-ash","title":"Set of Three Plinths 500mm Square Graduated in Solid Ash","description":"\u003cp\u003eThe wider version of the graduated three, for objects that need a bigger top than a 400mm square gives them.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: Three plinths at 500mm square, heights 700mm, 900mm, 1100mm\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm on every plinth in the set\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: solid English ash, pale and straight grained, finished in hardwax oil, sprayed in one batch so the whole set matches\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg per plinth evenly distributed\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no locks, these are open plinths\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 100.8 kilograms for the set\u003c\/li\u003e\n\u003cli\u003eSet contains three plinths\u003c\/li\u003e\n\u003cli\u003eFinish: sprayed as one batch, which is why a set matches and three separate orders do not\u003c\/li\u003e\n\u003cli\u003eSaving against buying them singly: about 10 per cent\u003c\/li\u003e\n\u003cli\u003eBallasted on anything over 900mm\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eExtra plinths can be added later and we keep the batch record for five years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThree plinths, flat packed\u003c\/li\u003e\n\u003cli\u003eLevelling feet for every plinth\u003c\/li\u003e\n\u003cli\u003eAn access panel in each with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 100ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003cli\u003eA layout card with three arrangements that work\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785468842316,"sku":"PLS-PST-019-ST","price":2449.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785468875084,"sku":"PLS-PST-019-CT","price":2599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Set_of_Three_Plinths_500mm_Square_Graduated_in_Solid_Ash.jpg?v=1789126067"},{"product_id":"display-plinth-500mm-by-500mm-by-900mm-high-in-gallery-white-lacquer","title":"Display Plinth 500mm by 500mm by 900mm High in Gallery White Lacquer","description":"\u003cp\u003eA 500mm square plinth at 900mm tall, in gallery white lacquer. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 900mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm moisture resistant MDF sprayed in a two pack polyurethane to RAL 9010, which is the white almost every gallery in the country paints its walls\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 31.7 kilograms\u003c\/li\u003e\n\u003cli\u003eHollow, and it can be weighted through the access panel\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785480638796,"sku":"PLS-PLI-077-ST","price":729.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785480671564,"sku":"PLS-PLI-077-CT","price":769.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_900mm_High_in_Gallery_White_Lacquer.jpg?v=1789057365"},{"product_id":"display-plinth-500mm-by-500mm-by-900mm-high-in-matt-black-lacquer","title":"Display Plinth 500mm by 500mm by 900mm High in Matt Black Lacquer","description":"\u003cp\u003eA 500mm square plinth at 900mm tall, in matt black lacquer. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 900mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm MDF sprayed in a two pack polyurethane to RAL 9005 in a dead matt, which swallows reflections and is why photographers ask for it\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 31.7 kilograms\u003c\/li\u003e\n\u003cli\u003eHollow, and it can be weighted through the access panel\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785480704332,"sku":"PLS-PLI-078-ST","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785480737100,"sku":"PLS-PLI-078-CT","price":789.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_900mm_High_in_Matt_Black_Lacquer.jpg?v=1789057368"},{"product_id":"display-plinth-500mm-by-500mm-by-900mm-high-in-birch-plywood","title":"Display Plinth 500mm by 500mm by 900mm High in Birch Plywood","description":"\u003cp\u003eA 500mm square plinth at 900mm tall, in birch plywood. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 900mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18 layer birch plywood with the edge exposed and lacquered, so the layers read as a fine stripe around every corner\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 29.8 kilograms\u003c\/li\u003e\n\u003cli\u003eHollow, and it can be weighted through the access panel\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785480769868,"sku":"PLS-PLI-079-ST","price":639.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785480802636,"sku":"PLS-PLI-079-CT","price":679.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_900mm_High_in_Birch_Plywood.jpg?v=1789057372"},{"product_id":"display-plinth-500mm-by-500mm-by-900mm-high-in-solid-ash","title":"Display Plinth 500mm by 500mm by 900mm High in Solid Ash","description":"\u003cp\u003eA 500mm square plinth at 900mm tall, in solid ash. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 900mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: solid English ash, pale and straight grained, finished in hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 33.6 kilograms\u003c\/li\u003e\n\u003cli\u003eHollow, and it can be weighted through the access panel\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785480835404,"sku":"PLS-PLI-080-ST","price":899.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785480868172,"sku":"PLS-PLI-080-CT","price":959.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_900mm_High_in_Solid_Ash.jpg?v=1789057369"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-gallery-white-lacquer","title":"Display Plinth 500mm by 500mm by 1100mm High in Gallery White Lacquer","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in gallery white lacquer. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm moisture resistant MDF sprayed in a two pack polyurethane to RAL 9010, which is the white almost every gallery in the country paints its walls\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 37.1 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785480900940,"sku":"PLS-PLI-081-ST","price":839.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785480933708,"sku":"PLS-PLI-081-CT","price":889.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Gallery_White_Lacquer.jpg?v=1789057369"},{"product_id":"display-plinth-500mm-by-500mm-by-1100mm-high-in-matt-black-lacquer","title":"Display Plinth 500mm by 500mm by 1100mm High in Matt Black Lacquer","description":"\u003cp\u003eA 500mm square plinth at 1100mm tall, in matt black lacquer. Standard gallery height, which puts a small object at eye level.\u003c\/p\u003e\u003cp\u003eA plinth is a simple object and almost every cheap one gets the same three things wrong. The panel is too thin, so the top deflects under a bronze and you can see it from across the room. The corners are mitred and glued rather than lock jointed, so they open after one move and the paint cracks at the arris. And there is no ballast, so a tall plinth with a light object on it can be knocked over by somebody walking past with a coat. Ours are 18mm on a braced internal frame, lock jointed at every corner, and ballasted at the base on anything over 900mm tall.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 500mm deep by 1100mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm by 500mm, flat within 0.5mm across the diagonal\u003c\/li\u003e\n\u003cli\u003eConstruction: 18mm moisture resistant MDF on a braced internal frame, lock jointed at every corner\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm MDF sprayed in a two pack polyurethane to RAL 9005 in a dead matt, which swallows reflections and is why photographers ask for it\u003c\/li\u003e\n\u003cli\u003eLoad rating: 310kg evenly distributed, 155kg point load in the centre\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: no lock, this is an open plinth\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed, two person delivery to the room, packaging taken away on the same visit if you ask when you book\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 37.1 kilograms\u003c\/li\u003e\n\u003cli\u003eBallasted base on anything over 900mm tall\u003c\/li\u003e\n\u003cli\u003eAccess panel in the back for cable, weight or a lock\u003c\/li\u003e\n\u003cli\u003eCorner detail: lock jointed, not mitred, so it survives a move\u003c\/li\u003e\n\u003cli\u003eTouch up paint supplied in the exact batch\u003c\/li\u003e\n\u003cli\u003eCut to a non standard height for 6 per cent more, chosen at order\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe plinth, flat packed\u003c\/li\u003e\n\u003cli\u003eFour levelling feet\u003c\/li\u003e\n\u003cli\u003eA removable access panel with a captive fixing\u003c\/li\u003e\n\u003cli\u003eA 50ml pot of the exact finish for touching up\u003c\/li\u003e\n\u003cli\u003eA hex key, a spanner and printed instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eIt arrives flat packed with a hex key, a spanner and printed instructions. Fittings are cam locks into steel inserts rather than screws into board, so it comes apart for a move and goes back together square. Level it on the feet before anything goes on top, and check it with a level across both diagonals rather than along the front, because a gallery floor is almost never flat and a plinth that follows the floor is the thing everybody notices and nobody can name.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eTwo rules cover most of it. The top of a plinth should be a little smaller than the footprint of the object, not larger, because a visible margin of empty plinth reads as a mistake and an object that slightly overhangs reads as deliberate. And the height should put the centre of the work between 1300 and 1500mm off the floor, which is eye level for most people standing at a comfortable viewing distance. For a small object that means a tall plinth, which people resist and should not. If in doubt, send us the dimensions and weight of the piece and we will tell you the size we would use.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785480966476,"sku":"PLS-PLI-082-ST","price":859.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785480999244,"sku":"PLS-PLI-082-CT","price":909.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Display_Plinth_500mm_by_500mm_by_1100mm_High_in_Matt_Black_Lacquer.jpg?v=1789057372"},{"product_id":"three-tier-corner-plant-stand-in-powder-coated-steel","title":"Three Tier Corner Plant Stand in Powder Coated Steel","description":"\u003cp\u003eA plant stand rated for the weight of a pot when it is wet rather than when it is dry, which is roughly double and is the number most stands are not designed around.\u003c\/p\u003e\u003cp\u003ePlants are heavier than people expect and wetter than furniture likes. A 400mm pot of wet compost is about 25 kilograms, and a stand that is fine for a sculpture will eventually rack under it. Everything in this part of the range is rated wet rather than dry, and everything that a pot sits directly on is either sealed or supplied with a tray, because the commonest way to ruin a good stand is to water the plant on it.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm across by 1200mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm top with a sealed surface and a 10mm lip\u003c\/li\u003e\n\u003cli\u003eConstruction: welded or mortice and tenon frame, depending on the material\u003c\/li\u003e\n\u003cli\u003eFinish: 2mm folded steel, welded and ground before coating so no seam shows, in a fine texture powder coat\u003c\/li\u003e\n\u003cli\u003eLoad rating: 87kg wet, tested at that weight for 30 days\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: not applicable\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed or assembled depending on the size\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 17.7 kilograms\u003c\/li\u003e\n\u003cli\u003eWet rating: 87kg, which is a 450mm pot of soaked compost\u003c\/li\u003e\n\u003cli\u003eTop: sealed and lipped, so a spill stays on the stand\u003c\/li\u003e\n\u003cli\u003eDrip tray: a matching tray is available and we recommend it\u003c\/li\u003e\n\u003cli\u003eFeet: sealed and felt padded, so water does not wick into the base\u003c\/li\u003e\n\u003cli\u003eTakes a pot up to 460mm across\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe stand\u003c\/li\u003e\n\u003cli\u003eFelt pads and a spare set\u003c\/li\u003e\n\u003cli\u003eLevelling feet where the height needs them\u003c\/li\u003e\n\u003cli\u003eA hex key where it is flat packed\u003c\/li\u003e\n\u003cli\u003eA watering note, because the commonest way to ruin a stand is to water the plant on it\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eArrives assembled and blanket wrapped. Stand it where you want it, level it on the feet, and take the wrapping back to the van, which the delivery crew will do.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eMatch the stand to the pot and not to the plant. A stand should be a little narrower than the pot so the pot reads as the object, and it needs to carry the weight of the compost wet rather than dry, which is roughly double. Height is worth thinking about for the plant rather than for the room: most house plants want to be up in the light rather than down at ankle level, and a plant on a 700mm stand next to a window will outgrow the same plant on the floor beside it inside a season.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785487421772,"sku":"PLS-PLT-022-ST","price":329.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785487454540,"sku":"PLS-PLT-022-CT","price":349.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Three_Tier_Corner_Plant_Stand_in_Powder_Coated_Steel.jpg?v=1789126170"},{"product_id":"three-tier-corner-plant-stand-in-solid-oak","title":"Three Tier Corner Plant Stand in Solid Oak","description":"\u003cp\u003eA plant stand rated for the weight of a pot when it is wet rather than when it is dry, which is roughly double and is the number most stands are not designed around.\u003c\/p\u003e\u003cp\u003ePlants are heavier than people expect and wetter than furniture likes. A 400mm pot of wet compost is about 25 kilograms, and a stand that is fine for a sculpture will eventually rack under it. Everything in this part of the range is rated wet rather than dry, and everything that a pot sits directly on is either sealed or supplied with a tray, because the commonest way to ruin a good stand is to water the plant on it.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm across by 1200mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm top with a sealed surface and a 10mm lip\u003c\/li\u003e\n\u003cli\u003eConstruction: welded or mortice and tenon frame, depending on the material\u003c\/li\u003e\n\u003cli\u003eFinish: solid European oak, 20mm panels on a braced frame, finished in a hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 87kg wet, tested at that weight for 30 days\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: not applicable\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed or assembled depending on the size\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.8 kilograms\u003c\/li\u003e\n\u003cli\u003eWet rating: 87kg, which is a 450mm pot of soaked compost\u003c\/li\u003e\n\u003cli\u003eTop: sealed and lipped, so a spill stays on the stand\u003c\/li\u003e\n\u003cli\u003eDrip tray: a matching tray is available and we recommend it\u003c\/li\u003e\n\u003cli\u003eFeet: sealed and felt padded, so water does not wick into the base\u003c\/li\u003e\n\u003cli\u003eTakes a pot up to 460mm across\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe stand\u003c\/li\u003e\n\u003cli\u003eFelt pads and a spare set\u003c\/li\u003e\n\u003cli\u003eLevelling feet where the height needs them\u003c\/li\u003e\n\u003cli\u003eA hex key where it is flat packed\u003c\/li\u003e\n\u003cli\u003eA watering note, because the commonest way to ruin a stand is to water the plant on it\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eArrives assembled and blanket wrapped. Stand it where you want it, level it on the feet, and take the wrapping back to the van, which the delivery crew will do.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eMatch the stand to the pot and not to the plant. A stand should be a little narrower than the pot so the pot reads as the object, and it needs to carry the weight of the compost wet rather than dry, which is roughly double. Height is worth thinking about for the plant rather than for the room: most house plants want to be up in the light rather than down at ankle level, and a plant on a 700mm stand next to a window will outgrow the same plant on the floor beside it inside a season.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785487487308,"sku":"PLS-PLT-023-ST","price":409.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785487520076,"sku":"PLS-PLT-023-CT","price":429.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Three_Tier_Corner_Plant_Stand_in_Solid_Oak.jpg?v=1789126165"},{"product_id":"three-tier-corner-plant-stand-in-solid-ash","title":"Three Tier Corner Plant Stand in Solid Ash","description":"\u003cp\u003eA plant stand rated for the weight of a pot when it is wet rather than when it is dry, which is roughly double and is the number most stands are not designed around.\u003c\/p\u003e\u003cp\u003ePlants are heavier than people expect and wetter than furniture likes. A 400mm pot of wet compost is about 25 kilograms, and a stand that is fine for a sculpture will eventually rack under it. Everything in this part of the range is rated wet rather than dry, and everything that a pot sits directly on is either sealed or supplied with a tray, because the commonest way to ruin a good stand is to water the plant on it.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm across by 1200mm high\u003c\/li\u003e\n\u003cli\u003eDisplay surface: 500mm top with a sealed surface and a 10mm lip\u003c\/li\u003e\n\u003cli\u003eConstruction: welded or mortice and tenon frame, depending on the material\u003c\/li\u003e\n\u003cli\u003eFinish: solid English ash, pale and straight grained, finished in hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 87kg wet, tested at that weight for 30 days\u003c\/li\u003e\n\u003cli\u003eLevelling: four M10 levelling feet with 20mm of travel, recessed so nothing shows and nothing catches a toe\u003c\/li\u003e\n\u003cli\u003eSecurity: not applicable\u003c\/li\u003e\n\u003cli\u003eDelivery: flat packed or assembled depending on the size\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.1 kilograms\u003c\/li\u003e\n\u003cli\u003eWet rating: 87kg, which is a 450mm pot of soaked compost\u003c\/li\u003e\n\u003cli\u003eTop: sealed and lipped, so a spill stays on the stand\u003c\/li\u003e\n\u003cli\u003eDrip tray: a matching tray is available and we recommend it\u003c\/li\u003e\n\u003cli\u003eFeet: sealed and felt padded, so water does not wick into the base\u003c\/li\u003e\n\u003cli\u003eTakes a pot up to 460mm across\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe stand\u003c\/li\u003e\n\u003cli\u003eFelt pads and a spare set\u003c\/li\u003e\n\u003cli\u003eLevelling feet where the height needs them\u003c\/li\u003e\n\u003cli\u003eA hex key where it is flat packed\u003c\/li\u003e\n\u003cli\u003eA watering note, because the commonest way to ruin a stand is to water the plant on it\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eArrives assembled and blanket wrapped. Stand it where you want it, level it on the feet, and take the wrapping back to the van, which the delivery crew will do.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eMatch the stand to the pot and not to the plant. A stand should be a little narrower than the pot so the pot reads as the object, and it needs to carry the weight of the compost wet rather than dry, which is roughly double. Height is worth thinking about for the plant rather than for the room: most house plants want to be up in the light rather than down at ankle level, and a plant on a 700mm stand next to a window will outgrow the same plant on the floor beside it inside a season.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Standard height","offer_id":58785487552844,"sku":"PLS-PLT-024-ST","price":369.0,"currency_code":"GBP","in_stock":true},{"title":"Cut to your height","offer_id":58785487585612,"sku":"PLS-PLT-024-CT","price":389.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Three_Tier_Corner_Plant_Stand_in_Solid_Ash.jpg?v=1789126168"},{"product_id":"tabletop-display-case-500mm-by-300mm-by-400mm-high-with-a-gallery-white-lacquer-base","title":"Tabletop Display Case 500mm by 300mm by 400mm High with a Gallery White Lacquer Base","description":"\u003cp\u003eA glass case on a gallery white lacquer base, sized for a wide shallow case for a model, a knife or a fossil. Sits on a table, a shelf or the top of one of our plinths.\u003c\/p\u003e\u003cp\u003eA vitrine is a box that has to disappear. Everything we do to one is aimed at that: low iron glass because ordinary float glass has a green cast that shows on every edge, mitred and polished glass corners rather than an aluminium post, and a base sized so the glass sits proud of it rather than inside a visible rebate. The unglamorous half is the part that keeps the object safe. Dust gets in through the base, not the top, so every case here has a gasketed base and a felt sealed door, which is the single biggest thing you can do for anything that has to stay clean for ten years.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 300mm deep by 400mm high overall\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal display area 480mm by 280mm by 340mm\u003c\/li\u003e\n\u003cli\u003eConstruction: solid base with a rebated glass seat, glass mitred and polished at the vertical corners\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm moisture resistant MDF sprayed in a two pack polyurethane to RAL 9010, which is the white almost every gallery in the country paints its walls\u003c\/li\u003e\n\u003cli\u003eLoad rating: 50kg on the deck\u003c\/li\u003e\n\u003cli\u003eLevelling: felt pads on the base\u003c\/li\u003e\n\u003cli\u003eSecurity: a cam lock is available as an option\u003c\/li\u003e\n\u003cli\u003eDelivery: one carton, assembled, the glass in a fitted cradle\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGlass: 4mm, mitred and polished, choose the specification at order\u003c\/li\u003e\n\u003cli\u003eTop lifts off, and it needs two hands on anything over 500mm\u003c\/li\u003e\n\u003cli\u003eDust: a felt seated rebate, which is what keeps it clean\u003c\/li\u003e\n\u003cli\u003eBase height: 60mm, sprayed on all faces\u003c\/li\u003e\n\u003cli\u003eSits on a plinth top, and our 300 and 400mm plinths are sized for these\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe base, assembled and sprayed\u003c\/li\u003e\n\u003cli\u003eThe glass case in a fitted cradle\u003c\/li\u003e\n\u003cli\u003eA felt seating strip, fitted\u003c\/li\u003e\n\u003cli\u003eFelt pads for the base and a spare set\u003c\/li\u003e\n\u003cli\u003eA microfibre cloth and a care note\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eThe base arrives flat packed and the glass arrives assembled in its own crate. Build and level the base first, then two people lift the glass on. Do not lift a glass case by the top rail. The gasket seats itself under the weight of the glass, so leave it for an hour before you load the case and check the door line again after a day.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Toughened float glass","offer_id":58785489027404,"sku":"PLS-TDC-007-TG","price":339.0,"currency_code":"GBP","in_stock":true},{"title":"Low iron glass, no green edge","offer_id":58785489060172,"sku":"PLS-TDC-007-LI","price":409.0,"currency_code":"GBP","in_stock":true},{"title":"Laminated UV filtering glass","offer_id":58785489092940,"sku":"PLS-TDC-007-UV","price":459.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Tabletop_Display_Case_500mm_by_300mm_by_400mm_High_with_a_Gallery_White_Lacquer_Base.jpg?v=1789126154"},{"product_id":"tabletop-display-case-500mm-by-300mm-by-400mm-high-with-a-matt-black-lacquer-base","title":"Tabletop Display Case 500mm by 300mm by 400mm High with a Matt Black Lacquer Base","description":"\u003cp\u003eA glass case on a matt black lacquer base, sized for a wide shallow case for a model, a knife or a fossil. Sits on a table, a shelf or the top of one of our plinths.\u003c\/p\u003e\u003cp\u003eA vitrine is a box that has to disappear. Everything we do to one is aimed at that: low iron glass because ordinary float glass has a green cast that shows on every edge, mitred and polished glass corners rather than an aluminium post, and a base sized so the glass sits proud of it rather than inside a visible rebate. The unglamorous half is the part that keeps the object safe. Dust gets in through the base, not the top, so every case here has a gasketed base and a felt sealed door, which is the single biggest thing you can do for anything that has to stay clean for ten years.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 300mm deep by 400mm high overall\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal display area 480mm by 280mm by 340mm\u003c\/li\u003e\n\u003cli\u003eConstruction: solid base with a rebated glass seat, glass mitred and polished at the vertical corners\u003c\/li\u003e\n\u003cli\u003eFinish: 18mm MDF sprayed in a two pack polyurethane to RAL 9005 in a dead matt, which swallows reflections and is why photographers ask for it\u003c\/li\u003e\n\u003cli\u003eLoad rating: 50kg on the deck\u003c\/li\u003e\n\u003cli\u003eLevelling: felt pads on the base\u003c\/li\u003e\n\u003cli\u003eSecurity: a cam lock is available as an option\u003c\/li\u003e\n\u003cli\u003eDelivery: one carton, assembled, the glass in a fitted cradle\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGlass: 4mm, mitred and polished, choose the specification at order\u003c\/li\u003e\n\u003cli\u003eTop lifts off, and it needs two hands on anything over 500mm\u003c\/li\u003e\n\u003cli\u003eDust: a felt seated rebate, which is what keeps it clean\u003c\/li\u003e\n\u003cli\u003eBase height: 60mm, sprayed on all faces\u003c\/li\u003e\n\u003cli\u003eSits on a plinth top, and our 300 and 400mm plinths are sized for these\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe base, assembled and sprayed\u003c\/li\u003e\n\u003cli\u003eThe glass case in a fitted cradle\u003c\/li\u003e\n\u003cli\u003eA felt seating strip, fitted\u003c\/li\u003e\n\u003cli\u003eFelt pads for the base and a spare set\u003c\/li\u003e\n\u003cli\u003eA microfibre cloth and a care note\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eThe base arrives flat packed and the glass arrives assembled in its own crate. Build and level the base first, then two people lift the glass on. Do not lift a glass case by the top rail. The gasket seats itself under the weight of the glass, so leave it for an hour before you load the case and check the door line again after a day.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Toughened float glass","offer_id":58785489125708,"sku":"PLS-TDC-008-TG","price":349.0,"currency_code":"GBP","in_stock":true},{"title":"Low iron glass, no green edge","offer_id":58785489158476,"sku":"PLS-TDC-008-LI","price":419.0,"currency_code":"GBP","in_stock":true},{"title":"Laminated UV filtering glass","offer_id":58785489191244,"sku":"PLS-TDC-008-UV","price":469.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Tabletop_Display_Case_500mm_by_300mm_by_400mm_High_with_a_Matt_Black_Lacquer_Base.jpg?v=1789126168"},{"product_id":"tabletop-display-case-500mm-by-300mm-by-400mm-high-with-a-solid-oak-base","title":"Tabletop Display Case 500mm by 300mm by 400mm High with a Solid Oak Base","description":"\u003cp\u003eA glass case on a solid oak base, sized for a wide shallow case for a model, a knife or a fossil. Sits on a table, a shelf or the top of one of our plinths.\u003c\/p\u003e\u003cp\u003eA vitrine is a box that has to disappear. Everything we do to one is aimed at that: low iron glass because ordinary float glass has a green cast that shows on every edge, mitred and polished glass corners rather than an aluminium post, and a base sized so the glass sits proud of it rather than inside a visible rebate. The unglamorous half is the part that keeps the object safe. Dust gets in through the base, not the top, so every case here has a gasketed base and a felt sealed door, which is the single biggest thing you can do for anything that has to stay clean for ten years.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 300mm deep by 400mm high overall\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal display area 480mm by 280mm by 340mm\u003c\/li\u003e\n\u003cli\u003eConstruction: solid base with a rebated glass seat, glass mitred and polished at the vertical corners\u003c\/li\u003e\n\u003cli\u003eFinish: solid European oak, 20mm panels on a braced frame, finished in a hardwax oil\u003c\/li\u003e\n\u003cli\u003eLoad rating: 50kg on the deck\u003c\/li\u003e\n\u003cli\u003eLevelling: felt pads on the base\u003c\/li\u003e\n\u003cli\u003eSecurity: a cam lock is available as an option\u003c\/li\u003e\n\u003cli\u003eDelivery: one carton, assembled, the glass in a fitted cradle\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 15.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGlass: 4mm, mitred and polished, choose the specification at order\u003c\/li\u003e\n\u003cli\u003eTop lifts off, and it needs two hands on anything over 500mm\u003c\/li\u003e\n\u003cli\u003eDust: a felt seated rebate, which is what keeps it clean\u003c\/li\u003e\n\u003cli\u003eBase height: 60mm, sprayed on all faces\u003c\/li\u003e\n\u003cli\u003eSits on a plinth top, and our 300 and 400mm plinths are sized for these\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe base, assembled and sprayed\u003c\/li\u003e\n\u003cli\u003eThe glass case in a fitted cradle\u003c\/li\u003e\n\u003cli\u003eA felt seating strip, fitted\u003c\/li\u003e\n\u003cli\u003eFelt pads for the base and a spare set\u003c\/li\u003e\n\u003cli\u003eA microfibre cloth and a care note\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eThe base arrives flat packed and the glass arrives assembled in its own crate. Build and level the base first, then two people lift the glass on. Do not lift a glass case by the top rail. The gasket seats itself under the weight of the glass, so leave it for an hour before you load the case and check the door line again after a day.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Toughened float glass","offer_id":58785489355084,"sku":"PLS-TDC-009-TG","price":479.0,"currency_code":"GBP","in_stock":true},{"title":"Low iron glass, no green edge","offer_id":58785489387852,"sku":"PLS-TDC-009-LI","price":559.0,"currency_code":"GBP","in_stock":true},{"title":"Laminated UV filtering glass","offer_id":58785489420620,"sku":"PLS-TDC-009-UV","price":639.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Tabletop_Display_Case_500mm_by_300mm_by_400mm_High_with_a_Solid_Oak_Base.jpg?v=1789126158"},{"product_id":"acrylic-display-cover-500mm-by-300mm-by-400mm-high","title":"Acrylic Display Cover 500mm by 300mm by 400mm High","description":"\u003cp\u003eA five sided acrylic cover with bonded corners, for putting over an object that is already sitting on something. Lighter than glass, safer than glass and easier to post, which is why most collectors start here.\u003c\/p\u003e\u003cp\u003eAcrylic and glass are not interchangeable and it is worth knowing which you want. Acrylic is about half the weight, will not shatter, and can be posted, which matters if the object is not in the same building as you. It also scratches, holds a static charge that attracts dust, and yellows very slowly in strong daylight unless it is the UV filtering grade. Glass does none of those things and weighs twice as much. For anything that gets handled often, take acrylic. For anything that sits still for twenty years, take glass.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDimensions: 500mm wide by 300mm deep by 400mm high externally\u003c\/li\u003e\n\u003cli\u003eDisplay surface: internal area 494mm by 294mm by 397mm\u003c\/li\u003e\n\u003cli\u003eConstruction: 3mm cast acrylic, corners bonded and polished, five sided with an open base\u003c\/li\u003e\n\u003cli\u003eFinish: clear as standard, UV filtering as an option\u003c\/li\u003e\n\u003cli\u003eLoad rating: not applicable, this is a cover\u003c\/li\u003e\n\u003cli\u003eLevelling: sits on your own surface or on one of our bases\u003c\/li\u003e\n\u003cli\u003eSecurity: not applicable\u003c\/li\u003e\n\u003cli\u003eDelivery: one carton, with a protective film on both faces\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 3.6 kilograms\u003c\/li\u003e\n\u003cli\u003eCast acrylic, not extruded, which is what stops the corners crazing\u003c\/li\u003e\n\u003cli\u003eCorners bonded rather than screwed, so there is no visible fixing\u003c\/li\u003e\n\u003cli\u003eProtective film on both faces, peel it after it is in position\u003c\/li\u003e\n\u003cli\u003eAnti static cloth supplied, because acrylic attracts dust and a dry duster makes it worse\u003c\/li\u003e\n\u003cli\u003eA matching sprayed base is available in the same footprint\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat you get\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe acrylic cover with the film on\u003c\/li\u003e\n\u003cli\u003eAn anti static microfibre cloth\u003c\/li\u003e\n\u003cli\u003eA small bottle of acrylic safe cleaner\u003c\/li\u003e\n\u003cli\u003eA care note explaining what not to clean it with, which is most things\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eArrives assembled and blanket wrapped. Stand it where you want it, level it on the feet, and take the wrapping back to the van, which the delivery crew will do.\u003c\/p\u003e\u003ch3\u003eSpecifying it\u003c\/h3\u003e\u003cp\u003eSize the case to the object plus the space around it rather than to the object. A rule that works well is a clear 100mm at the sides and 150mm above for anything under half a metre, and more for anything a visitor will walk around. Think about the door before you buy: a hinged door needs swing space and a lift off top needs two people and somewhere to put a large piece of glass. If the case will hold anything light sensitive, take the UV filtering glass, and keep the light level at 50 lux for works on paper and textiles and 150 lux for oil, wood and most other things.\u003c\/p\u003e","brand":"Plinth Studio","offers":[{"title":"Clear cast acrylic","offer_id":58785491648844,"sku":"PLS-ACR-007-AC","price":154.95,"currency_code":"GBP","in_stock":true},{"title":"UV filtering cast acrylic","offer_id":58785491681612,"sku":"PLS-ACR-007-AU","price":189.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1091\/8300\/9100\/files\/Acrylic_Display_Cover_500mm_by_300mm_by_400mm_High.jpg?v=1789057374"}],"url":"https:\/\/plinthstudiostore.com\/collections\/500mm-footprint.oembed","provider":"Plinth Studio","version":"1.0","type":"link"}